Search found 12 matches
- Thu Feb 20, 2014 11:25 am
- Forum: K-Pro / KManager
- Topic: Kpro Launch Control
- Replies: 2
- Views: 2219
Re: Kpro Launch Control
Awesome thank you!
- Thu Feb 20, 2014 10:09 am
- Forum: K-Pro / KManager
- Topic: Kpro Launch Control
- Replies: 2
- Views: 2219
Kpro Launch Control
What input(sensor, switch, etc.) is used to use launch control? In the help section it says it's not suitable to use the start/clutch kill switch and cruise control cut switch but instead to use a micro switch. If I were to use a micro switch which circuit would this tie into? Thanks.
- Fri May 17, 2013 11:49 am
- Forum: K-Pro / KManager
- Topic: AFR Wideband vs Kpro
- Replies: 1
- Views: 2179
AFR Wideband vs Kpro
How accurate is the Kpro afr readings compared to an afr wideband gauge? Im in the process of tuning just wanted to know. Obviously a wideband is better but how close is the accuracy.
- Tue Aug 21, 2012 9:31 am
- Forum: Non-Hondata
- Topic: Engine running temperature
- Replies: 1
- Views: 3972
Engine running temperature
I have a 2002 Acura RSX Type S JRSC. What is the best engine running temperature for great gas mileage and performance on a K series motor?
- Tue Jul 17, 2012 6:10 am
- Forum: K-Pro / KManager
- Topic: P1259 Vtec System Malfunction, Possible ECM issue
- Replies: 7
- Views: 9493
Re: P1259 Vtec System Malfunction, Possible ECM issue
Vtec pressure switch is disabled and I just got back from a test drive and the light didn't come back on after womping on it several times.
- Mon Jul 16, 2012 5:32 pm
- Forum: K-Pro / KManager
- Topic: P1259 Vtec System Malfunction, Possible ECM issue
- Replies: 7
- Views: 9493
Re: P1259 Vtec System Malfunction, Possible ECM issue
I will disable the vtec pressure switch tomorrow morning and repost. Visiting a relative in the hospital. Does the vtec switch have anything to do with the engaging part of it? Will I lose my crossover when I disable it?
- Sat Jul 14, 2012 6:33 am
- Forum: K-Pro / KManager
- Topic: P1259 Vtec System Malfunction, Possible ECM issue
- Replies: 7
- Views: 9493
Re: P1259 Vtec System Malfunction, Possible ECM issue
Yeah I have non-stock injectors RC 440's.
- Sat Jul 14, 2012 6:30 am
- Forum: K-Pro / KManager
- Topic: P1259 Vtec System Malfunction, Possible ECM issue
- Replies: 7
- Views: 9493
Re: P1259 Vtec System Malfunction, Possible ECM issue
On the side of the ecu it says:
37820-PRB-305
2054-101106
The pin out case on the inside says:
37820-PRB-305
2054-101106-0K12
The hondata card says:
K-Pro
10459
I cleared all codes last night while at operating temperature and I did "ALOT" of WOT pulls and no vtec system malfunction codes ...
37820-PRB-305
2054-101106
The pin out case on the inside says:
37820-PRB-305
2054-101106-0K12
The hondata card says:
K-Pro
10459
I cleared all codes last night while at operating temperature and I did "ALOT" of WOT pulls and no vtec system malfunction codes ...
- Fri Jul 13, 2012 1:48 pm
- Forum: K-Pro / KManager
- Topic: P1259 Vtec System Malfunction, Possible ECM issue
- Replies: 7
- Views: 9493
P1259 Vtec System Malfunction, Possible ECM issue
2004 Acura RSX Type-S
JRSC 5lbs.
70mm Throttle Body
Stock K20a2
Hondata Kpro
I reset the ecm. Test drove it and accelerated past 4000 rpms, check engine light comes on. P1259 Vtec System Malfunction. I have continuity at the vtec pressure switch. I have battery voltage at terminal 1 of the vtec ...
JRSC 5lbs.
70mm Throttle Body
Stock K20a2
Hondata Kpro
I reset the ecm. Test drove it and accelerated past 4000 rpms, check engine light comes on. P1259 Vtec System Malfunction. I have continuity at the vtec pressure switch. I have battery voltage at terminal 1 of the vtec ...
- Tue Jun 12, 2012 1:46 pm
- Forum: K-Pro / KManager
- Topic: MAP doesn't read boost, only vacuum
- Replies: 4
- Views: 2390
Re: MAP doesn't read boost, only vacuum
Thank you
- Tue Jun 12, 2012 1:28 pm
- Forum: K-Pro / KManager
- Topic: MAP doesn't read boost, only vacuum
- Replies: 4
- Views: 2390
Re: MAP doesn't read boost, only vacuum
Well that makes more sense now. Do the MAP relocators come with the supercharger assembly? Is this a block that bolts the MAP on top while supplying a vacuum line to one of the runner ports? Sorry, pictures don't really show much from what I see.
- Tue Jun 12, 2012 12:53 pm
- Forum: K-Pro / KManager
- Topic: MAP doesn't read boost, only vacuum
- Replies: 4
- Views: 2390
MAP doesn't read boost, only vacuum
2002 Acura RSX Type-s K20a2 6 speed
JRSC with 5 lb pulley
70mm Throttle body
440 RC Injectors
DCRH, Test pipe, Catback
Absolutely no vacuum leaks. Idles at 21.9 in hg at 750 rpms. Boost gauge jumps to 5 pounds respectively. TPS has been rescaled and double checked. Watched and recorded map readings ...
JRSC with 5 lb pulley
70mm Throttle body
440 RC Injectors
DCRH, Test pipe, Catback
Absolutely no vacuum leaks. Idles at 21.9 in hg at 750 rpms. Boost gauge jumps to 5 pounds respectively. TPS has been rescaled and double checked. Watched and recorded map readings ...