Search found 8 matches
- Sat Aug 30, 2014 9:27 am
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
Re: help with odd no start/ runs poor
ok got it sorted out. jumper harness was pinned wrong. swapped in a diff harness and fired up and worked fine. went thru the original harness and found the wires for tdc/ cyp were not right. re pinned the jumper and re installed it no more issues . off to the dyno next fri and hopefully will be all ...
- Wed Aug 27, 2014 9:57 am
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
Re: help with odd no start/ runs poor
What is the serial number on the s300 inside the ECU?
From Help, About, what is the version of software you are using?
its the new white board ,s300 30366 i will have to fire the lap top back up later to get the other version number, but i just uninstalled and re installed it on sat and checked ...
From Help, About, what is the version of software you are using?
its the new white board ,s300 30366 i will have to fire the lap top back up later to get the other version number, but i just uninstalled and re installed it on sat and checked ...
- Tue Aug 26, 2014 10:59 pm
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
Re: help with odd no start/ runs poor
contacted precision and got the correct values for the 780s. reloaded base map with updated numbers. started but running crazy rich and still poor idle. ran for a few min shut down to make some adjustments. now wont start again. tried reloading map. even going to stock map with updated injector ...
- Tue Aug 26, 2014 8:58 am
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
Re: help with odd no start/ runs poor
i found a few places that list dead times for them , but only 680 cc and 1000 cc. reset values to the numbers for the 680cc and will see how much that helps
i came up with 1.56 1.36 1.22 1.13 1.05 .96 ( voltage from 10v- 15v )
current values were 1.49 1.49 .96 .68 .49 .35
i came up with 1.56 1.36 1.22 1.13 1.05 .96 ( voltage from 10v- 15v )
current values were 1.49 1.49 .96 .68 .49 .35
- Tue Aug 26, 2014 8:27 am
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
Re: help with odd no start/ runs poor
precision low imp 780 ccAREA876 wrote:What brand injectors are they?
- Mon Aug 25, 2014 7:52 am
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
Re: help with odd no start/ runs poor
what should i set for them / where do i find what it should be?AREA876 wrote:Do you have the dead time for the 780 injectors?, try entering the correct dead times and start from there.
- Sun Aug 24, 2014 9:03 pm
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
Re: help with odd no start/ runs poor
update. played with it more tonight. tried known good map sensor, no change. check voltages at sensor as well as ecm pins and all check ok.
tried a few diff base maps and don't seem to have any effect on it and was having issues with sensors displaying any values but yet the ecm green light is on ...
tried a few diff base maps and don't seem to have any effect on it and was having issues with sensors displaying any values but yet the ecm green light is on ...
- Sun Aug 24, 2014 6:29 pm
- Forum: s300 / SManager
- Topic: help with odd no start/ runs poor
- Replies: 10
- Views: 5117
help with odd no start/ runs poor
hey everyone just finished up a new build and loaded base map, car started ok and ran for about 3-5 min ( kinda poorly, low sluggish idle ) then stalled now wont restart. rechecked everthing in smanager and says everything is good. no cel/ dtc stored. tried a few other maps to see if it was related ...